Skip to content

Bulk Material Bags Calculator

Give the surface you want to cover, as length and width or as an area, the depth of the layer and the size of one bag in litres or cubic feet, and you get the volume in cubic metres and cubic yards and the number of bags to buy, rounded up. Add a settling margin in percent if the material will pack down, and a density in kilograms per cubic metre to see the weight of a bag and of the whole load. It also shows the area one bag covers. It runs in your browser and nothing you type is sent anywhere.

Bags to buy

25

500 L needed.
Volume in cubic metres
0.5 m³
Volume in cubic yards
0.654 yd³
Material left in the bags
0 L
One bag covers (at this depth)
0.4 m²

Volume = area × depth; bags = ⌈volume × (100 + margin) ÷ 100 ÷ bag size⌉. The settling margin is yours to choose: loose material packs down once it is spread and watered, so a margin gives you more bags, and 0 gives the plain volume. The weight uses the density you type, in kg per cubic metre; it changes a lot with moisture, so treat it as an estimate. A bag sold as a given size may hold slightly less: check the label.

How it works

  1. Choose metric or imperial, then type the length and the width of the surface, or switch to a direct area.
  2. Type the depth of the layer and the size of one bag, in litres or cubic feet.
  3. Optionally add a settling margin in percent, and a density in kg/m³ to get weights.
  4. Read the volume, the number of bags and the weight, and copy the summary.

What people use it for

  • Mulching a flower bed

    A 10 m² bed with a 5 cm layer is 500 litres, so 25 bags of 20 litres.

  • Spreading gravel on a path

    Add a density to see how heavy the bags are before you carry or order them.

  • Allowing for settling

    Add 10 % to a 500 litre layer and see the count rise from 25 to 28 bags.

Questions

How are the volume and the bags calculated?
Volume = area × depth. In metric, 1 m² at 1 cm deep is 10 litres, so 10 m² at 5 cm is 500 litres, which is 0.5 m³ or about 0.654 yd³. In imperial, 1 ft² at 1 in deep is 1/12 ft³. Bags = ⌈volume × (100 + margin) ÷ 100 ÷ bag size⌉: 500 litres in bags of 20 litres is exactly 25 bags, and 500.1 litres would be 26. The calculation uses exact decimals.
What is the settling margin?
Loose material packs down once it is spread and watered, so some people add a few percent. The page does not pick a value: it is 0 by default, which gives the plain volume, and you can type any value from 0 to 100. The cubic metres and cubic yards shown are always the volume without the margin, and the margin changes only the number of bags.
How is the weight estimated?
Weight of a bag = bag size in cubic metres × density, and the total is that figure times the number of bags. The density is yours to type, in kg per cubic metre, from 0.001 to 30,000; it varies a lot with the material and with moisture, so treat the weight as an estimate. Leave it empty to hide the weights. Pounds are given next to kilograms.
Which values are refused, and what is not covered?
Lengths and widths must be between 0.001 and 100,000, an area up to 1,000,000,000, a depth up to 100,000 and a bag size up to 1,000,000, in the unit shown, and more than 1,000,000,000 bags is refused. A bag sold as a given size may hold slightly less, and the page does not know how thick a layer your material needs: check the label, and do not treat the result as advice about a particular project.