Skip to content

Stair Rise and Run Calculator

Type the height you have to climb, the height you would like each step to have and the depth of a tread, and you get the number of risers rounded to the nearest whole step, the real height of each riser once the climb is divided evenly, the number of treads, the length the stair takes on the floor, the sloping length of the stringer and the angle of the slope. It also compares twice the riser plus the tread with an old rule-of-thumb range, as a hint only. It works in centimetres or inches, runs in your browser and sends nothing anywhere.

Number of risers (steps up)

15

Each riser is 18 cm high, exactly your target.
Treads (one fewer than risers)
14
Run along the floor
350 cm
Stringer length (sloping side)
442.04 cm
Slope angle
37.6°
2 × riser + tread (rule of thumb)
61 cm: inside the usual rule-of-thumb range of 57 to 64 cm.

Risers = total rise ÷ target rounded to the nearest whole number (a half goes up, at least 1); real riser = total rise ÷ risers; treads = risers − 1, because the floor above is the last step; stringer = √(rise² + run²). The tread depth is the horizontal going, with no nosing overhang. The 2R + G comparison is only an old rule of thumb (57 to 64 cm), not a building code: check the rules and the safety requirements that apply to your project before building.

How it works

  1. Choose centimetres or inches and type the total rise, from the finished floor below to the finished floor above.
  2. Type the riser height you would like and the depth of one tread.
  3. Read the number of risers, the real riser height, the treads, the run and the stringer length.
  4. Look at the rule-of-thumb line, change the target or the tread until it suits you, and copy the summary.

What people use it for

  • Sketching a stair before drawing it

    Turn a 270 cm floor-to-floor height into 15 risers of 18 cm and see how much floor length the 14 treads take.

  • Comparing two riser targets

    Change the target from 18 to 17 and watch the number of risers and the real height move before you decide.

  • Cutting the stringer

    Read the sloping length and the angle to know how long a board must be before you buy it.

Questions

How are the risers, the treads and the run calculated?
Risers = total rise ÷ target height, rounded to the nearest whole number (an exact half goes up) and never below 1. The real riser = total rise ÷ risers, so every step has the same height. Treads = risers − 1, because the floor above counts as the last step, and run = treads × tread depth. With a total rise of 270 cm, a target of 18 cm and a tread of 25 cm you get 15 risers of 18 cm, 14 treads and a run of 350 cm. The stringer is √(rise² + run²), 442.04 cm here, and the angle is the arctangent of rise ÷ run, about 37.6 degrees.
What is the 2 × riser + tread line?
It is an old rule of thumb that a comfortable step has twice the riser plus the tread between about 57 and 64 cm, which the page shows in inches too (22.4 to 25.2 in). The page only says whether your numbers fall inside, below or above that range. It is not a building code, it does not say that a stair is legal or safe, and the limits for riser height, tread depth, headroom and handrails depend on where you build: check the rules that apply to your project.
Which values are refused?
The total rise, the target height and the tread depth must each be between 0.001 and 100,000 in the chosen unit, and a result of more than 10,000 risers is refused with a message. A total rise below 1.5 times the target gives a single riser, because the count is the total rise ÷ target rounded to the nearest whole number (26.99 with a target of 18 gives 1, 27 gives 2). With a single riser the run is 0, the page says it is a step, not a slope, shows the angle as 90 degrees and leaves out the 2 × riser + tread line, since there is no tread to compare. The tread depth is the horizontal going, without any nosing overhang.
What is left out?
Landings, winders, curved stairs, the thickness of the floor finish, headroom and the width of the stair are not handled. Real floors are rarely perfectly level, so measure the total rise on site and treat the result as a starting point for your drawing, not as a cutting list.