Skip to content

Wallpaper Roll Calculator

Enter the length of all your walls added together, the height of the room, the width and the length of one roll and, if the paper has a pattern, the repeat, and you get the number of strips to hang, how many strips one roll gives, and the number of rolls to buy. The page counts strips across the width of the walls, which is how paper is really hung, and tells you how many strips are left over in the last roll. Metric and imperial units are both supported, and the arithmetic stays in your browser.

Rolls needed

7

27 strips, 4 strips from each roll.
Length of each strip (height + repeat)
2.5 m
Strips left over in the last roll
1
Area of the walls
35 m²
Paper bought (rolls × width × length)
37.29 m²

Strips = ⌈perimeter ÷ roll width⌉; strips from one roll = ⌊roll length ÷ (height + pattern repeat)⌋; rolls = ⌈strips ÷ strips per roll⌉. The full pattern repeat is added to every strip as a cautious allowance, and no trimming allowance is added: it is an estimate, so check the roll label and ask your supplier about the batch.

How it works

  1. Choose metric or imperial, then add the lengths of all the walls to be papered to get the perimeter.
  2. Type the wall height, the roll width and the roll length, and the pattern repeat if there is one, or 0 for a plain paper.
  3. Optionally type the area of the doors and windows, which is shown but not subtracted.
  4. Read the strips, the strips per roll and the rolls, and copy the summary.

What people use it for

  • Buying paper for a bedroom

    A 14 m perimeter, a 2.5 m height and rolls of 0.53 × 10.05 m need 27 strips, 4 per roll, so 7 rolls.

  • Seeing what a pattern costs

    Add a 64 cm repeat and watch the strips per roll drop, so that the rolls needed go up.

  • Checking a quote in feet and inches

    Switch to imperial and enter a 20.5 in roll that is 27 ft long to compare it with a supplier's figure.

Questions

How are the strips and the rolls calculated?
Strips = ⌈perimeter ÷ roll width⌉, strips from one roll = ⌊roll length ÷ (height + pattern repeat)⌋ and rolls = ⌈strips ÷ strips per roll⌉. With a 14 m perimeter, a 2.5 m height and a 0.53 × 10.05 m roll with no repeat, that is 27 strips, 4 strips per roll and 7 rolls, with 1 strip left over. Divisions are done on exact decimals, so 5.3 m of wall with a 53 cm roll gives exactly 10 strips and 5.31 m gives 11.
Why are the doors and windows not subtracted?
Strips are counted by width, not by area, and a strip beside or above a door or a window still has to be cut at the full height. Taking the opening off the area would give too few strips. The area you type is only shown, for information, with the wall area without it. It must not be larger than the area of the walls.
How is the pattern repeat used?
The full repeat is added to the height of every strip as a cautious allowance, so each strip is cut height + repeat long, which lowers the number of strips per roll. A repeat of 0 means a plain paper. Real paper can need less, depending on the type of match, so this is an estimate. If a strip is longer than a roll, the page says so instead of giving a number.
Which values are refused, and what is not included?
Lengths, widths and the roll size must be between 0.001 and 1,000,000 in the unit shown, the pattern repeat is 0 or more, and a total of more than 1,000,000,000 strips is refused. No trimming allowance, no skirting boards and no ceiling are added, and slanted or arched walls are not handled. Check the roll label and the batch number with your supplier.